IEC Equipment Reliability Testing – Part 4: Statistical Procedures for Exponential Distribution – Point Estimates, Confidence Intervals, Prediction. Buy IEC EQUIPMENT RELIABILITY TESTING – PART 4: STATISTICAL PROCEDURES FOR EXPONENTIAL DISTRIBUTION – POINT ESTIMATES. Buy IEC Ed. Equipment reliability testing Part 4: Statistical procedures for exponential distribution – Point estimates, confidence intervals, prediction.
|Published (Last):||20 August 2017|
|PDF File Size:||5.23 Mb|
|ePub File Size:||13.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Proceed to Checkout Continue Shopping. Describes guidelines for the collection of data relating to reliability, maintainability, availability, and maintenance support performance in the field. Describes 66005 application guide to reliability stress screening for electronic hardware.
Find Similar Items This product falls into the following categories. Risk analysis of technological systems. Standardization of data-collection practices facilitates the exchange of information between parties, e.
The resulting test cycle should be included in the detailed reliability test specification. Describes guidelines for selecting and implementing risk analysis techniques for quality and consistency in planning and execution for risk analysis. Describes the use of failure rate data for reliability prediction of components in electronic equipment including the effects of complexity, stress models for conversion.
IEC | IEC Webstore
This part of IEC provides a general procedure for design of test cycles, where no applicable preferred test cycles can be found in IEC A wide variety of subjects are available from IEC International Electrical Congress TC subcommittee for publications Technical Committee 56 is responsible for dependability issues driven by a strategic policy statement.
Idc and diagnostic testing. This standard is not included in any packages.
The major technical changes with respect to the previous edition concern the inclusion of corrected formulae for tests previously included in a corrigendum, and the addition of new methods for the analysis of multiple items. Indoor portable equipment-Low degree of simulation. Describes aspects of verification necessary oec ensure that the specified maintainability requirements of an item have been met and provides suitable procedures and test methods.
It applies to the design ie operating and environmental test cycles referred to in 8. This part of IEC provides a general introduction to the concept of life cycle costing and covers all applications. Subscription pricing is determined by: You may delete a document from your Alert Profile at any time.
Examples, guidelines, and principles for the exchange and merging of such RM data are addressed. The basis of the decision as to whether to include pre-exposure tests is outside the scope of this standard. Add to Alert PDF. Endurance testing, Statistical methods of analysis, Confidence intervals, Estimation, Exponential distribution, Electrical testing, Reliability, Statistical tolerance intervals, Statistical testing, Performance.
BS IEC 60605-4:2001
The main changes with respect to the previous edition are as follows: Describes procedures for modeling system reliability to calculate reliability and availability measures and contains a standard set of symbols related to reliability parameters. This standard has been withdrawn. Describes procedures for compliance test plans for success ratio or failure ratio tests where each trial is statistically independent. Describes Markov analysis methods for modeling maintenance strategies along with failure restorations events displayed in a pictorial way.
It is not intended to ifc a complete guide on how to specify or to contract for maintainability. Design of test cycles.
This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. The files of this standards is not available in the store right now. Your basket is empty. Application guide- Section 2: Application guide- Reliability test conditions and statistical test principles. Outdoor transportable equipment — Low degree of simulation. This document was withdrawn in and replace by IEC for Reliability stress screening-Part 1: The following main categories of data are to be collected: You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
Take the smart route to manage medical device compliance. Guide to the specification of dependability requirements. Life cycle models are used to describe product development or project phases. Replaced by IEC Ed 1. This may be due ief a requirement or for the purpose of assessing the behaviour in time of the failure rate or the failure intensity.
OVE webshop – IEC
It also identifies typical life cycle cost elements to facilitate project and programme planning. Describes procedures to estimate the parameters of the power law model along with confidence 6005 for failure intensity, and prediction intervals for the time to future failures along with a test of goodness of fit to data from repaired items. Describes processes which are applicable for hardware items which have unacceptably low reliability in the early failure periods and when other methods irc as reliability grow plots are not applicable.
It described the general approach in reaching these objectives and shows ho maintainability characteristics should be specified in a requirements document or contract.