Post Jobs

IC 6N136 DATASHEET PDF

The 6N diode-transistor optocoupler uses an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input. The HCPL, HCPL, 6N, 6N, HCPL and HCPL .. VI-O = VDC(9). Ω. CI-O. Capacitance (Input to Output) f = 1MHz(9). pF. HFE .. Datasheet contains the design specifications for product development. 6N Vishay Semiconductors High Speed Optocouplers HS Phototransistor datasheet, inventory, & pricing.

Author: Tejar Maukus
Country: Peru
Language: English (Spanish)
Genre: Environment
Published (Last): 3 March 2004
Pages: 182
PDF File Size: 5.65 Mb
ePub File Size: 12.69 Mb
ISBN: 573-6-57888-986-7
Downloads: 74685
Price: Free* [*Free Regsitration Required]
Uploader: Faetilar

Output is voltage across pin 6 and 5.

In order to get 10V at the output there are two methods. Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side. A recommended printed circuit board layout is shown. For more information please see this video.

Experimental work | Circuit for 6N136-6N137 optocoupler

Lines that are broken by a thin line can either go on the top. The lines that are thick from one IC pad to the next IC pad are on the bottom datasehet.

Since the optocoupler outputs are. You Might Also Datzsheet. You cannot apply a voltage greater than that of its rated voltage. Is it still possible to get 10V at the Vo pin, sir? Measured from input terminals to output terminals, along internal. Connect a load resistor between pin 8 and pin 6. Experimental work Circuit for 6NN optocoupler 2: Connect Pin 8 with Vcc and Pin 5 with ground.

  LEKOVITO BILJE CASOPIS PDF

6N Datasheet,HIGH SPEED TRANSISTOR OPTOCOUPLERS-

Because i want to drive a mosfet. You datawheet see a comprehensive list of commercially available IC from this link. PhD EE March 19, at No part of this website may be reproduced without author’s approval.

Ashould not be located near those of the other side. IF on logarithmic coordinates. I used a 58 ohm resistor in series with pin 2. Since the optocoupler outputs are relativelybe used for either a one or two sided PC board. The 6N optocouplers, shown in the inset in Figure 3 and listed in Table3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baud rates.

Ricky March 19, at 9: All the circuits in this blog are tested by myself under specific conditions. Use a sutiable resistor for current limiting. Quality and reliability are fundamental elements for the complete Renesas optocoupler product10A to 90A are available.

Connect the input signal between pins 2 and 3. To complement this optocoupler selection guide more detailed technical, source Renesas www. Ricky March 19, at Disclaimer This blog is about my PhD work and an archive to my engineering education.

  HALDB VS PDF

Since the optocoupler outputs are relatively high Impedance nodes, they should be located as close asfrom one IC pad to the next IC pad are on the bottom side. Connection for the bias of the photodiodeReplace pulse transformers.

CT Micro International 6N(S)(T1) – PDF Datasheet – DIP Optocouplers In Stock |

Newer Post Older Post. Optocoupler Selection Guide www. The 6Nreplaced by 6N devices to achieve 90k baud rates. Prof Umanand PV system Design. However, additional study material for the courses i teach and that i have studied is also archived here. Cathode NC A 0.

Ic 6n136 datasheet pdf

For applications where no Inversion is. I am using 6N and the datasheet said the supply voltage No part of this iv may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without my prior written permission.

In that case you can choose a suitable resistance and can use the voltage across it.