Post Jobs


The AX/TF Series of long range photoelectric detectors with selectable beam frequencies. The selectable beam frequencies can be used to avoid. The Optex AXTF is an outdoor 4-channel select dual beam photoelectric detector featuring a detection range and a form C relay output. Searching for a low cost Photoelectric Detector solution? The Optex AXTF is a great Photoelectric Detector within our Photoelectric Detectors product line at.

Author: Muzilkree Tegis
Country: Liechtenstein
Language: English (Spanish)
Genre: Travel
Published (Last): 14 March 2008
Pages: 232
PDF File Size: 11.72 Mb
ePub File Size: 8.43 Mb
ISBN: 634-7-98764-227-8
Downloads: 32780
Price: Free* [*Free Regsitration Required]
Uploader: Neshicage

Re-program the Zone’s Loop Response Time” appropriately. Unpacking In the box with the B housing you will find a small plastic bag containing: In the box with the B housing you will find a small plastic bag containing: Section – Wiring. The trouble signal output continues as long as the beam strength is below an acceptable level.


Turn mirror base by hand to obtain the highest alignment level. Check to see that input power is within the product’s requirements.

TE This unit is designed to detect an intruder and activate an alarm control panel. No false alarm shall occur within these operating condition. Never attempt to disassemble or repair the product.

Optex – OP-AXTF – ‘ OD 4 Chan Select Dual Beam(Compatib

The precise area of the detection field shall be specific to each model. Adjust the vertical alignment screw to obtain the maximum voltage from the monitor jack. Photoelectric detectors detect intruders when both the upper and lower invisible infrared beams are simultaneously broken.


Is the control panel zone’s Loop Response Time” set to within 1 second? Documents Flashcards Grammar checker. Be the first to review this product.

Lightning and surge protection up to 15Kv Anti — 650yf design Easy installation and alignment Twin beams require simultaneous interruption to create activation Sealed optics to prevent ingress az insects and dust Adjustable beam interruption time AX — PLUS — detection range 75m Ordering no.

AX-250PLUS, AX-500PLUS AX-350TF, AX-650TF

Each LED shall indicate 3 steps of alignment, slow 650f is okay, fast flicker is better, continuously ON is the best, totally providing 15 graduated stages. Remove the power wires from Power supply’s output terminals. Remove any objects or move the beams. Do not align both beams simultaneously. It will reset when the environmental conditions clear.

It may cause fire or damage to the devices. The Detector features More information.

YES There is a possibility that the power line has been cut. Before starting, read the. Can easily obtain maximum optical alignment by checking the voltage from this jack. It may cause electric shock. User s Manual Before using the inverter, you need to read and save the safety instructions.

Wiring Distance When using two or more units on one wire, the maximum length is obtained by dividing the wire length listed below by the number of units used. The detector shall contain an A. They shall require simultaneous interruption of both beams to trigger an activation ; no activation shall be generated when birds, insects, or falling leaves break just one beam.

  FWD-42PX2 & PDF

Detector transparent with Color Inserts. Operation of Alarm Memory If the units is triggered during an armed period, when the system is disarmed, its LED will remain lit to confirm that it reported the alarm.

For Bi Xenon kits only: Detects transparent bottles that have a lens effect. Make the horizontal and vertical adjustments to the lower mirrors. Safety Operation Maintenance More information.

Quad and Twin Photobeam Detectors. In order to get the most out of this instrument for many years to come, please take the More information. Output of the detector or switch must 650t N. In front of the Receiver. Start display at page:.

Failure to follow the safety rules and other 650f safety precautions. Change footing, pole or structure to insure a stable mounting surface. At the middle point between Transmitter and Receiver.

And loosen the unit base mounting screw and remove mounting plate by sliding it down against the unit base.