L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked _机械 /仪表_工程科技_专业资料。ASTM A Standard.
|Published (Last):||28 June 2008|
|PDF File Size:||8.54 Mb|
|ePub File Size:||2.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
Material Test Report and Certi? A superscript epsilon e indicates an editorial change since the last revision or reapproval. The noncontrolling factor normally will exceed considerably the speci? This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions.
ASTM A Standard Specification for Annealed or Cold-Worked_百度文库
An alternative method of determining? This abstract is a brief summary of the referenced standard. Last previous edition approved in as A — However, in the case of dispute, tests shall be made by pressure. C Annealed material that naturally meets mechanical properties may be applied.
The values obtained in this manner should not, however, be taken as the actual yield strength for 0. One bend test shall be made from one end of each coil. A number in parentheses indicates the year of last reapproval. ICS Number Code A66 case of dispute, the offset method of determining yield strength shall be used. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Referenced Documents purchase aa666 The documents listed below are referenced within the subject standard but are not provided as part of the standard.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This revision of Speci?
The values given in parentheses are for information only. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? Hard Elongation in 2 in. Historical Version s – view previous versions of standard. HardC Elongation in 2 in. This standard has been approved for use by agencies of the Department of Defense.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract asm accurate, complete or up to date. They shall be formed in different shapes such as sheets, strips, plates and flat bars. zstm
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? Only annealed conditions of grades specifically approved by the ASME code ast permitted for pressure vessel use. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Link to Active This link will always route to the current Active version of the standard. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. Only annealed conditions of grades speci? Your comments are invited either for revision of this asgm or for additional standards and should be addressed to ASTM International Headquarters.
Users of this standard are expressly advised that determination of the validity of any such axtm rights, and the risk of infringement of such rights, are entirely their own responsibility.
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Current edition approved Oct. The values given in parentheses are for information only. B Maximum unless otherwise indicated.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
The steels shall adhere to specified chemical composition requirements.
Number of Tests 8. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Originally approved in A — 03 Standard Speci?
Rockwell B 95 95 Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling q666 in meeting the properties. The choice of test method for materials in conditions other than annealed shall astk at the option of the seller. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. D PSS means plate, strip, sheet.