Post Jobs

ASTM A564 PDF

Best Stainless offers high quality standards including UNS S, AMS , ASTM A, and ASTM A Grade PH stainless steel can be used. This standard is issued under the fixed designation A /A M; the number . [ mm] round bar, 10 to 12 ft [ to m] in length, ASTM A See the chemical composition and physical properties of ASTM A Grade condition HM, find alternative materials, and connect with suppliers.

Author: Gagar Taushakar
Country: Anguilla
Language: English (Spanish)
Genre: Technology
Published (Last): 13 December 2012
Pages: 319
PDF File Size: 10.25 Mb
ePub File Size: 13.26 Mb
ISBN: 322-5-11797-680-9
Downloads: 69553
Price: Free* [*Free Regsitration Required]
Uploader: Ducage

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Up to 6 in. G Columbium 8 times carbon minimum.

17-4 PH Stainless Steel Bar

This standard has been approved for use by agencies of the Department of Defense. Applications should be limited to small diameter bar. The tests shall meet the requirements of Table 4.

Mechanical Properties Requirements 7. C Columbium plus tantalum 0. A sstm epsilon indicates an editorial change since the last revision or reapproval.

They are suitable for machining in the solution-annealed condition after which they may be age-hardened to the mechanical properties specied in Section 7 without danger of cracking or distortion.

They are suitable for machining in the solution-annealed condition after which they may be age-hardened to the mechanical properties specified satm Section 7 without danger of cracking or distortion. Billets or bars for reforging may be purchased to this specification. Warm in air to room temperature.

The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. A 87 [] 58 [] Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

  GELFAND FOMIN PDF

They are suitable for machining in the solution-annealed condition after which they may be age-hardened to the mechanical properties specified in Section 7 without danger of cracking or distortion. The material shall be subjected to tension, impact, and hardness tests.

ASTM A564 – Martensitic Stainless Steel

They are suitable for machining in the solution-annealed condition after which they may be age-hardened to a546 mechanical properties specified in Section 7 without danger of cracking or distortion. Active view current version of standard. Type XM is machinable in the as-received fully heat treated condition.

Current edition approved May 1, C Unless otherwise noted, temperatures shown are suggested temperatures and may be varied to obtain required tensile properties. Shapes may be subjected to either Class A or Class C preparation for removal of visible surface imperfections. asgm

Link to Active This link will always route to the current Active version of the standard. C Either Rockwell C hardness or Brinell is permissible. Up to 12 in. Historical Version s – view previous wstm of standard. G Either Rockwell C hardness or Brinell is permissible.

Work Item s – proposed revisions of this standard. Combining values from the two systems may result in nonconformance with the specification. Materials and Manufacture 5. Limits are in percent maximum unless shown as a range or stated otherwise.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. I A5564 to Table 2 for details on equalize and over temper heat treatment. The specimens shall be heat treated in accordance with 5. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

  DISTEMPER TRATAMIENTO PDF

Number of Tests 8.

PH Stainless Steel Bar – ASTM A Supplier | Best Stainless

Applications should be limited to ast diameter bar. Material of types other than XM, XM, and Type shall be furnished in the solution-annealed condition, or in the equalized and oven-tempered condition. Such requirements may include but are not limited to the following: F Columbium plus tantalum 0. Note 2 — For billets and bars for forging see Specification A Type UNS S is suitable for machining in the solution-annealed, cold-worked, and aged-hardened condition. Type UNS S shall be furnished in solution annealed, cold-worked or aged-hardened condition.

Type XM is machinable in the as-received fully heat treated condition. Type UNS S is suitable for machining in the solution-annealed, cold-worked, and aged-hardened condition. Your comments will receive careful consideration at a meeting of the responsible technical committee, which s564 may attend.

Hot-nished or cold-nished rounds, squares, hexagons, bar shapes, angles, tees, and channels are included; these shapes may be produced by hot rolling, extruding, or forging.